New products

At this point, we would like to draw your attention to some new products you will find in our catalog for the first time. In the table of contents of the catalog you will also find an overview with small illustrations and the page number. On these pages the products are described in more detail.

There is for instance the divisible rosette with circular grinding which is particularly interesting as a retrofit solution. The two-part product is connected with bores and pins by two square bars, which are concealed on the inside, and can be secured against slipping by means of a screw locking device.

The improved corner plate for the support of 90 degree corners allows simultaneous screwing of the adjacent pipes, the plate itself and the corner connector. As a result, a total of 4 components are permanently connected to the two mounting screws. Furthermore, the introduction of bores and assembly is considerably simplified by the longer limbs.

Our completely redesigned wall bracket allows screwing of rail posts and different distances to the mounting surface. In addition, it is possible to compensate for tolerances when mounting at the height of the console. With these components a very stable and secure fastening is possible.

The point holder in square design and the fork nuts with different gap dimensions allow the connection of round and angular point holders with M10 threads to 6/8 and 10 mm thick-walled substructures. This creates completely new possibilities for individual canopy structures.

Our completely redesigned counterbox is characterized by the same dimensions as the box locks. Due to the modified bolt-on situation of the striking plate, this product can be installed without height offset with or without E-opener. Furthermore, the product can be used on the right and left and is available in steel and stainless steel.

Please get an overview, familiarize yourself with the new catalog and exchange your old catalog with the new catalog. If you have any questions about our products, please do not hesitate to contact us. We are happy to help with suggestions and advice.


Here are some items that we have added to our product range:

blindbild
blindbild

AISI 304 Rosette divisible | Ø 105 x 22

Article 41305

blindbild
blindbild
blindbild

AISI 304 Connection plate 90 degrees long | for pipe Ø 42,4

Article 43273

blindbild
blindbild
blindbild

AISI 304 wall bracket with adjustable bracket | Ø 42.4 x 127 | For pipe Ø 42.4

Article 41188

blindbild
blindbild
blindbild

AISI 304 Stainless steel square bracket | 60 x 60 M10

Article 43302

blindbild
blindbild
blindbild

AISI 304 bowl with round grinding | Ø 42 x 2

Article 41352

blindbild
blindbild
blindbild

AISI 304 Stainless steel universal box | 172 x 60 x 40

Article 41535

blindbild



Archive product novelties 2016

In 2016 we have again designed new products, improved old products and rounded out the selection in some areas for you. Part of the new releases can also be found as a thumbnail image with cross-references in the table of contents of the catalogue on page 5.

We now offer our adhesive stopper with great insertion depth for pipes up to 4.0 mm wall thickness. For the strike boxes and box locks we have added new products and further extended the accessories.

We now offer 13 mm bore for the point fixings for daily mounting of glass panes on railings with filler rods . So that this can also be used on galvanized and/or galvanized and powder coated constructions.

The previous round model 50 with the glass clamps was supplemented by a new model 50 with solid ground. The optics are particularly delicate due to the extremely flat glass support. For this new product we have applied for approval with DIBT but at the time of writing this it has not yet been granted.

For shop fittings , advertising signs or other structures in which very small glass holders are required , we have a new mini clamp holder in the program. These delicate parts are suitable for flat and connecting pipes from Ø 26.9 mm and can be used to 8.76 mm clamping strength.

In addition to components made of steel and stainless steel the accessories from the Fischer company have been added. Technical information can be found in the download area of our website . To enable you to fit these products we now offer high quality SDS - Hammer drills.

Please familiarize yourself with the new catalogue and replace your old catalogue with the new one. If you have any questions about our products , do not hesitate to contact us. We are available with advice, suggestions, and practical help.


Here are some items that we have added to our product range:

blindbild
blindbild

V2A discs with center hole cut | for screw M8 DIN 7991 | Ø 35 x 5

Article 41371

blindbild
blindbild
blindbild

V2A Bar holder with end hole | Connection flat | Hole Ø 12.2

Article 41856

blindbild
blindbild
blindbild

V2A glass terminal with ground piece | L and R | for tube Ø 42.4

Article 43657 / 43658

blindbild
blindbild
blindbild

V2A Adjustable connector | Pipe Ø 42.4 x 2

Article 43226

blindbild
blindbild
blindbild

V4A anchor rod with ETA | FIS A | M10 x 130

Article 40642

blindbild
blindbild
blindbild

SDS Plus Hammer Drill | 4 carbide cutting | Double helix | Ø 14 x 300

Article 70081

blindbild
blindbild
blindbild

Fischer FIS V injection mortar 360 S | 2-K mortar with ETA approval

Article 70520


Archive product novelties 2015

In the endcap selection we offer a new variant. These caps are not knurled, but have a smooth surface for bonding. Through this installation, it is possible to carefully balance out the sometimes considerable weight from our standard pipes.

Our square plate holders are now, as the new round plate holders, completely revised and allow for mounting with the M8 cylinder head bolts through holes. On the opposite side, a standard M8 nut in the bracket is inserted.

For the connection of structural tubes we added new wall connections in the assortment, to allow for concealed mounting as wel as the assembly of pipes between two walls without a visible screw. We offer these parts for both round and square tubes.

The wall anchors range has been extended by two new models in which the pipe is inserted and glued down via a port. In addition to a model with spacer sleeves and a 8 mm wall plate. The mounting holes have a diameter of 11 or 13 mm, to allow for a stable connection to the wall.

In our anchor plates range, the assortment was extended too. Laser etched plates from 10 mm material and holes that correspond to the railing of the directive metalwork were included. Drilling has been partially increased due to the increased demands on fastening technology

The program was rounded off again and expanded in almost all areas. High-quality abrasives in the Accessories area and a completely new program in the locking mechanism accessories hopefully leave you curious to find out more. Browse through the new catalog and picture what it could all look like. .


Here are some items that we have added to our product range:

blindbild
blindbild

AISI 304 Domed end caps | tread M8 | Ø 42,4 x 2

Article 48017

blindbild
blindbild
blindbild

AISI 304 Blankholder square for sheet 1,5 – 4,0 | 25 x 25 | connection flat

Article 43216

blindbild
blindbild
blindbild

AISI 304 Wall connection round | Ø 50 x 40 | for tube Ø 42,4

Article 43209

blindbild
blindbild
blindbild

AISI 304 Wall anchors with adhesive connection | 90 x 120 x 6 | for tube Ø 42,4 x 2

Article 41154

blindbild
blindbild
blindbild

AISI 304 Wall anchors angular | 160 x 50 x 8 | for tube Ø 42,4 x 2

Article 41173

blindbild
blindbild
blindbild

Satinier fleece folding roller | 100 x 100 x 19 | Tube frame lock

Article 70176


Archive product novelties 2014

The new plate supports were completely revised and now allow mounting with M8 cylinder head screws in through borings. On the opposite side you may insert a standard M8 nut into the support.

Furthermore, metal sheets of 1,5 - 4.00 mm can be clamped with different rubbers. We have taken care that the outside is tightly fitting for each metal sheet thickness and that the head obtains a slight bulge with a round grinding, like with our cross bar supports.

The stainless steel knob for lock housings was completely revised and can now be adapted in 4 different directions. Moreover, their design was supplemented by a square version with square plate. This one can be combined with the short plates.

Here is not enough space to mention all details of the new, revised or added articles. We would only like to inspire you and hope you will have a look and use our parts on your building sites.


Here are some items that we have added to our product range:

blindbild
blindbild

AISI 304 sheet support for metal sheet 1.5 - 4.0 | Ø 30 x 47 | connection Ø 42.4

Article 43214 | view video

blindbild
blindbild
blindbild

AISI 304 stainless steel knob square| fixed knob | square plate | 60 x 40 x 22

Article 43134

blindbild
blindbild
blindbild

AISI 304 sleeve nut flat with Allen | M8 x 14 | for flat post

Article 40391

blindbild
blindbild
blindbild

AISI 304 handrail support | blank Ø 70 x 6 | punching 2 x Ø 8.5 lowered

Article 41243

blindbild
blindbild
blindbild

AISI 304 tube end piece with radius | Ø 42.4 x 30 | connection Ø 42,4

Article 41592


In the glass clamps sector we are now also providing parts that are made of duplex steel. This material quality (1.4462) allows us to use such building products even in high wear areas. Please, find further information on this subject and the general building approval for stainless steels in our download area.

Furthermore, we can now offer stainless steel handrail supports with clip rosettes. There are 3 mounted standard models but all individual parts may be separately obtained as well. In this system you can combine more than 150 different handrail supports and cover almost all areas of demand.


Here are some items that we have added to our product range:

blindbild
blindbild

Glass clamps with general building approval | DUPLEX STEEL 1.4462

Article DS 43520

blindbild
blindbild
blindbild

Handrail support system disc | for rosette 41200

Article 41287


Archive product novelties 2013
In addition to expanding our mounting and anchor plate program in steel and stainless steel, we focused the trend of angular shapes and added many new components to the catalog and the catalog extension 2013/2014.

In addition to the standard welded lugs in steel and stainless steel we now also offer square and customized parts for round tubes. In addition end caps for square tube with the dimensions 40 x 60 x 2 mm and lasered wall anchor S235.

Here are some items that we have added to our product range:

blindbild
blindbild

Final arcs, square | 40 x 40 x 2 mm

Article 43060

blindbild
blindbild
blindbild

Joint links, square | 40 x40 x 2 mm

Article 43062

blindbild
blindbild
blindbild

Wall ties, square | perforation 40 x 40 mm

Article 41148

blindbild
blindbild
blindbild

Lock plate, very long | for pipe frame lock

Article 43194

blindbild
blindbild
blindbild

Lock plate, blind | for standard case lock

Article 43192

blindbild
blindbild
blindbild

Profile cylinder rose, angular | universally applicable

Article 43128

blindbild
blindbild
blindbild

Flange, divisible | for round material Ø 12 mm

Article 41237

blindbild
blindbild
blindbild

Pipe support, universal | 42,4 x 2 mm

Article 43025



Be sure to order our free catalog to see all the products and rates.
Order catalog >>

Product news

Online shop registration

The online portal for our customers is open and product ordering please register here >>

New customer -Catalog ordering